充水时间,water-filling time
1)water-filling time充水时间
2)Filling Time充型时间
3)infilling time充注时间
4)charging time充电时间
1.Dsterminating thecharging time of capacitor in measuringhigh resistance with leakage current method;电容器漏电法测高阻中电容器充电时间的确定
2.For a capacitor discharge welding machine using a voltage-tracing charging mode,the mathematical model of the charging circuit was calculated and analyzed by computer to study the influence of circuit parameters on charging efficiency andcharging time ,and a group of perfect parameters to improve charging efficiency and reducecharging time were found out.针对采用电压跟踪式限流充电方式的大容量储能点焊机,借助于计算机对充电电路数学模型进行计算分析,研究了充电电路参数对充电时间和充电效率的影响,并找出合适的工作点,以提高充电效率,减小充电时间。
英文短句/例句
1.charging interval充电时间, 充电间隔
2.Time-Contnoling of Electric Bicycle Charger and Realization;电动自行车充电时间控制电路的实现
3.A Study on the Rule of Time of Charge for the High Voltage Circuit in ESA Fuzes引信ESA高压电路充电时间变化规律研究
4.Battery Capacity A completely discharged heavy-duty battery requires twice the charging time of a small capacity battery.电池容量 完全放电的重型电池需要小容量电池充电时间的两倍。
5.Tank size, supports, acid concentrations, charging schedule, plate alignment, etc. are the same as described.槽的尺寸，支架，酸的浓度，充电时间，极板的排列等与所描述的一样。
6.A shorter charging time may be used, but not recommended, because of the hazard involved.可以采用更短的充电时间，但不宜推荐，因为有危险性。
7.How long will it take to charge up the batter?给这个蓄电池充电要用多少时间？
8.Recharged cell inside, super long time playback.内置可充电电池，超长时间播放。
9.A fully charged headset battery provides approximately: 6 hours talk time ;100 hours standby time电池在充满电量情况下提供约：通话时间：6 小时；待机时间：100 小时
10.CMP battery uses the imported, original and high-capacity cell, after full charge of the battery, the using time is longer than the original, and the platform of discharge is high.CMP 电池采用进口原装高容量电芯，电池满充电后使用时间比原配电池时间长，放电平台高。
11.An insulating resistance can be calculated by measuring the Voltae decrease rate when a charged capacitor is discharged through the resistor and the voltage of capacitor is reduced from one value to another.充电电容对高值电阻放电,只要测量电容电压衰减的时间就可以算出电阻大小。
12."You can harvest enough electricity to power a cell phone battery for about four days from a spoonful of sugar."“用一勺糖，四天时间，获得的电能就可以充满手机电池。”
13.Instant and interval temporal operation extension based on ATSQL2基于ATSQL2时间点与时间段时态操作扩充
14.Over extended periods of time, batteries gradually wear down and require longer charging times. This is normal.随着使用时间，电池功能下降并需要较长时间进行充电，属于正常现象。
15.The unit of capacitance in the meter-kilogram-second system equal to the capacitance of a capacitor having an equal and opposite charge of1 coulomb on each plate and a potential difference of1 volt between the plates.法拉电容的单位，等于电容器极板上充以1库仑电量后两板间的电压为1伏特时的电容
16.I find that I have plenty of time now.我发觉我现在时间充裕。
17.We should make the most of our time.我们应该充分利用时间。
18.We must make the most of our time.我们必须充分利用时间。
相关短句/例句
Filling Time充型时间
3)infilling time充注时间
4)charging time充电时间
1.Dsterminating thecharging time of capacitor in measuringhigh resistance with leakage current method;电容器漏电法测高阻中电容器充电时间的确定
2.For a capacitor discharge welding machine using a voltage-tracing charging mode,the mathematical model of the charging circuit was calculated and analyzed by computer to study the influence of circuit parameters on charging efficiency andcharging time ,and a group of perfect parameters to improve charging efficiency and reducecharging time were found out.针对采用电压跟踪式限流充电方式的大容量储能点焊机,借助于计算机对充电电路数学模型进行计算分析,研究了充电电路参数对充电时间和充电效率的影响,并找出合适的工作点,以提高充电效率,减小充电时间。
5)Hyperemic time充血时间
6)filling time充模时间
1.Experimental Research on Effect of Pulsatile Injection Pressure on Filling Cavity Pressure and Filling Time;脉动注射压力影响充模压力及充模时间的实验研究
2.The optimization criterion of resin injection temperature,the way of calculating thefilling time(tfill) and the time of the low viscosity platform of resin(tplat) were put forward,based on the simulation of the RTM process and the research on the properties of the resin viscosity.在RTM工艺模拟及RTM工艺专用树脂黏度特性研究的基础上,提出充模时间与安全系数的乘积小于树脂低黏度平台时间的树脂注射温度优化标准和充模时间、树脂低黏度平台时间的计算方法,制定了程序化流程并编制了软件,使优化得以实施。
3.By the use of injection and compression molding,and with appropriate mould clamping force,thefilling time could be shortened in so far as possible.介绍了注射压缩成型的特点、过程、模具设计要求和相关设备要求,采用注射压缩成型可以缩短充模时间,充分利用注塑机合模结构的功能,在合理的合模力作用下,可以得到最短的充模时间。
延伸阅读
充炭黑充油丁苯橡胶分子式：分子量：CAS号：性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
