湿膜厚度,wet film thickness
1)wet film thickness湿膜厚度
英文短句/例句
1.If the required paint film thickness has not been achieved, the additional coats should be applied till the specified thickness is attained.如果未达到要求的湿膜厚度，应覆涂直到满足指定的湿膜厚。
2.Properties of MnWO_4-Li_2WO_4 system thick film humidity sensorsMnWO_4-Li_2WO_4系厚膜湿敏元件的性能
3.Method of test for measurement of dry film thickness of paintsGB/T1764-1979漆膜厚度测定法
4.testing method for film thickness of rust preventive oil防锈油膜厚度测定法
5.Study on the Correlation of Central Corneal Thickness and Corneal Epithelial Thickness in Rabbits兔角膜中央厚度与角膜上皮厚度的相关研究
6.Rabbit corneal thickness and the thickness of the cornea epithelial related research兔角膜中央厚度与角膜上皮厚度的相关性
7.Influencing factors of collapsibility coefficient of Lanzhou loess with large thickness兰州大厚度黄土湿陷系数的影响因素
8.Research on the Influence of Corneal Thickness on Corneal Flap Thickness in LASIK;准分子激光原位角膜磨镶术中角膜厚度对角膜瓣厚度影响的研究
9.Effects of film thickness on the properties of ferroelectric film薄膜厚度对铁电薄膜铁电性能的影响
10.A Comparison of Central Corneal Thickness Measurements by Specular Microscopy and Ultrasonic Pachymetrey角膜内皮细胞计与A超角膜测厚仪测量角膜中央厚度的比较
11.There is no pressure gradient through the thickness of the film.贯穿流体膜厚度无压力梯度。
12.Analysis and Calculation of the Width and Thickness of Ink-jet Printing Film喷墨印刷膜层宽度和厚度的分析计算
13.Determination of the Foundation Reasonable Reinforce Depth for Collapse Loess with Large Thickness大厚度湿陷性黄土场地地基处理深度的确定
14.Reasonable treatment depth for foundation of collapsing loess with a large thickness大厚度湿陷性黄土场地地基处理合理深度
15.Measurement of human retinal thickness at posterior pole with retinal thickness analyzer in normal and glaucomatous eyes用视网膜厚度分析仪测定正常眼及青光眼后极部视网膜厚度
16.Micrometer on instrument that can be used to measure thickness. Typically used to measure the dry film thickness of paint and the thickness of metal strip.千分尺—用来测量厚度的工具。通常用作测量涂膜的干膜厚度和带钢的厚度。
17.Resistive-type Humidity-sensitive Materials and Thin Film Humidity Sensors Based on Polyelectrolytes;聚电解质电阻型湿敏材料及薄膜湿度传感器
18.A Study ef the Ground Treatment for Self-weight Collapsible Loess With Large Thickness and Its Application大厚度湿陷性黄土地基处理的研究与应用
相关短句/例句
wet film thickner湿膜厚度计
3)lubricant film thickness油膜厚度
1.This paper had got overall introduction on many measurement technologies and detecting methods oflubricant film thickness, and on their disadvantages and application status in that of thrust bearing.较为全面、系统地介绍了润滑油膜的测量技术和各种检测方法的特点与不足,以及在推力轴承检测中的应用情况,这对于更好地进行推力轴承油膜厚度的检测有一定的参考价值。
4)oil film thickness油膜厚度
1.The influence ofoil film thickness variation on workpiece gauge control in rolling process is analyzed.分析了轧制过程油膜厚度变化对钢板厚度控制精度的影响,基于油膜厚度Reynolds计算公式,借鉴轧辊调零计算轧机弹跳的想法,提出相对油膜厚度的计算方法,并在轧机上进行数据采集,得到油膜变化的实测值,通过弹跳曲线的平移处理,得到最终的油膜变化曲线,根据该曲线可很方便地确定模型的结构并拟合出模型系数。
2.In order to analyze the influence ofoil film thickness of back-up roll dynamic oil film bearing in tandem cold rolling on strip thickness and to improve the AGC accuracy,oil film thickness experiment was done.为了分析冷连轧机支撑辊动压油膜轴承的油膜厚度变化对带钢厚度的影响,提高轧机AGC精度,进行了油膜厚度测试实验。
3.The hydrostatic slide’s principle,characteristic,classification,applicable situation were introduced,and the effect factors for slide design ,including load capacity,oil film rigidity,oil film thickness as well as slide clearance were analyzed.介绍了液体静压导轨工作原理、特点、分类及适用场合 ,分析了承载能力、油膜刚度、油膜厚度以及导轨间隙等静压导轨设计的影响因素。
5)thickness of oil film油膜厚度
6)film thickness漆膜厚度
1.The significance offilm thickness control during spraying by robot,influence factors thereof and adjustment of relevant parameters are discussed.讨论了机器人喷涂涂料时,漆膜厚度控制的意义、影响漆膜厚度的因素以及相应参数的调整方法。
2.Illstrating the importance of painting to product quality,discussing the approach to dertemining product paint consumptim in painting process and consequently determining the most reasonablefilm thickness to minimize paint consumption ,providing a useful referece for determination of paint consumption for similar products in painting process.阐述了产品油漆对产品质量影响性 ,讨论产品油漆工艺消耗定额的制定方法 ,制定最合理漆膜厚度 ,使油漆消耗量降至最低值 ,为同类产品油漆工艺消耗定额的制定提供了有益的参考。
延伸阅读
湿膜厚度计分子式：CAS号：性质：在漆膜制备后立即进行测量厚度的仪器。有轮规（wheel tube）和梳规（comb tube）。轮规由三个圆盘组成，外侧两个圆盘在某一半径处相切，该处的间隙为零，在相反关径处，间隔最大，外侧有刻度，指示不同间隙的读数；梳规为一正方形或矩形金属板或塑料片，在其4边都刻着带不同读数的齿，各齿距水平面有依次递升的不同间隙。湿膜厚度为沾湿的轮或齿的读数。
