最小切削厚度,minimum chip thickness
1)minimum chip thickness最小切削厚度
1.In micro-cutting,a chip will not be generated if the uncut chip thickness is less than a critical value,viz,theminimum chip thickness.最小切削厚度是微切削中产生切屑必须超过的切削厚度的临界值。
英文短句/例句
1.Minimum Chip Thickness in Orthogonal Micro-cutting Based on Plasticity Strain Gradient Theory基于应变梯度理论的正交微车削中最小切削厚度预测
2.maximum sawing or filling thickness of work工件锯割或锉削最大厚度
3.Permeability of Cutting Fluid in Minimum Quantity Lubrication Precision Turning最小量润滑精密车削中切削液的渗透性
4.minimum cover of reinforcement钢筋保护层的最小厚度
5.minimum thickness of neck缩颈的最小直径;颈部的最小厚度;颈部的最小厚度
6.Influence of Undeformed Chip Thickness on Surface Roughness-Spectral Analysis of the Profile of Machined Surface切削厚度对加工粗糙度的影响——已加工表面轮廓的谱分析
7.(2) Cutting speed influents chip dimension.(2)切削速度对切屑形状的尺寸大小有影响。
8.The Influence Analysis on Micro Orthogonal Turn-Milling Cutting Speed to Chip Formation;微小型正交车铣切削速度对切屑变形影响分析
9.The effects of different cutting thickness on surface quality and slice quality are studied in this paper.研究了不同切削厚度对竹材表面质量与屑片质量的影响。
10.flat-surface grinding machine, numerically controlled 0.01mm minimum accuracy数控平面磨削机,最小确度为0.01mm
11.flat-surface grinding machine, not numerically controlled 0.01mm minimum accuracy非数控平面磨削机,最小精确度为0.01mm
12.Minimum thicknesses in rim and centre of lensGB/T1205-1975透镜边缘及中心最小厚度
13.Study on Cutting Temperature under Ultrasonic Hard Turning 45 Hardened Steel超声硬切削45淬硬钢的切削温度研究
14.Remove all bone from the cuts and slice pieces into uniform thickness and size(approximately 3 inches thick).把这些牛肉块去骨并将其切成统一的厚度和大小(约3英寸厚)。
15.Shear force is interrelating with width and thickness of plate and obliquity of knife-edge.斜刃剪切时，剪切力的大小与板料的宽度、厚度及斜刃倾角有关。
16.Abstract: Shear force is interrelating with width and thickness of plate and obliquity of knife-edge.文摘:斜刃剪切时，剪切力的大小与板料的宽度、厚度及斜刃倾角有关。
17.cut small bits or pare shavings from.从……切下小点或削刮。
18.micrometer cutting depth adjustment千分表切削深度调整
相关短句/例句
cutting depth切削厚度
1.The relationship between sheer stresses andcutting depth is found.利用位错理论对超声波振动切削过程中剪切应力进行分析 ,从微观方面得出其计算公式 ,发现剪切应力与切削厚度的关
3)undeformed chip thickness切削厚度
1.Influences of the double negative chamfer angles of diamond turning tool and theundeformed chip thickness on the surface rolling effect are analyzed, and the empirical formulas of surface rolling rate are presented.对汽车轮毂抹平加工的主要工艺参数进行了试验研究 ,分析了金刚石抹平车刀双重负倒棱角度和切削厚度对抹平效果的影响 ,给出了抹平率经验公式。
4)Cutting thickness切削厚度
1.Study on the effects of cutting thickness of bamboo on its cutting quality;切削厚度对竹材刨切质量影响的研究
2.Aiming at the helical ball-end milling tool used in HSM,the milling force model of tool infinitesimal was built up,then the calculation method of instantaneous cutting thickness was presented,finally,a new whole milling force model was obtained by integral.针对高速铣削中广泛应用的螺旋刃球头铣刀建立刀具微元的铣削力模型,给出了瞬时切削厚度的计算方法,通过积分得出了一种新的整体铣削力模型。
3.The new method of cutting thickness analysis and compute is given out.介绍了插齿时产生齿面挤伤及插齿刀后面非正常磨损的特有现象,分析了其原因以及切屑的几种形态,给出了切削厚度分析计算的新方法,提出一套新见解和解决措施。
5)minimum cutting depth最小切削深度
1.To probe into machining mechanism in micro cutting,theminimum cutting depth for achieving stable machining was discussed.为探讨微切削的加工机理,对能稳定切削的最小切削深度进行了研究。
6)minimum cutting force最小切削力
延伸阅读
最小辐亮度与最小辐照度(见核爆炸火球)最小辐亮度与最小辐照度(见核爆炸火球)minimum-brightness and minimum-irradiancezuixiao fuliangdu yu zuixiaofu乙haodu最小辐亮度与最小辐照度(minimum-brightness and而nimum一irradianee)见核爆炸火球。
