微屈服强度,microyield strength
1)microyield strength微屈服强度
1.The influence of electric filed intensity during the process of aging in electric field on themicroyield strength and micro\|plastic deformation behavior of 2024 aluminum alloy was studied.研究了电场时效处理中电场强度对 2 0 2 4铝合金的微屈服强度和微变形行为的影响。
2.The measuring method of themicroyield strength has studied with the INSTRON testing equipment.利用INSTRON试验机研究了微屈服强度的测试方法。
2)Micro-yield Strength微屈服强度
1.Through comparison between the micro-yield strength value of and the corresponding yield strength value of more than 130 samples, it is shown that the tedious micro-yield tests can be replaced by common and simple yield tests.通过130多个铍试样的微屈服强度与屈服强度的比较试验证明,用常规简单的屈服强度试验代替冗长的微屈服强度试验是可能的。
2.We research the micro-yield strength of 1Cr18Ni9Ti steel under the high temperature aging treatment,provide mechanical parameters for mechanical engineering.测试1Cr18Ni9Ti合金钢高温时效处理状态下的微屈服强度,为工程实际提供力学参数。
3.Dimensional stability of sub-micron Al2O3 /2024Al composites was studied by means of micro-yield strength measurement and TEM analysis.本文利用微屈服强度测试和透射电镜分析,研究了亚微米级Al_2O_3颗粒增强2024Al复合材料的尺寸稳定性。
3)yield strength屈服强度
1.Effect of phosphorus on theyield strength of as-quenched GH761 alloy;磷对GH761合金固溶水淬组织屈服强度的影响
2.Study of influence factors ofyield strength of oil and gas pipeline;油气管道屈服强度影响因素的研究
3.A modeling study of theyield strength of HRB335 hot rolled ribbed bar;HRB335热轧带肋钢筋屈服强度模型研究
英文短句/例句
1."Yield strength 85Kg/mm2(120,000psi)maximum"屈服强度最大85Kg/mm2(120000psi)
2."Maximum shear Strength 63Kg/mm2(90,000psi) maximum (based on 75% yield) "剪切强度最大63Kg/mm2(90000psi)(为屈服强度的75%)
3.Study on Increasing Yield Strength of Q345B Plate in JISCO;提高酒钢Q345B板材屈服强度研究
4.Research on dynamic yield strength of steel 30CrMnSiNi2A30CrMnSiNi2A钢的动态屈服强度研究
5.Analysis of Cracking During Stamping of 700MPa Grade Super High Strength Beam Steel屈服强度700MPa级超高强度大梁钢冲压开裂分析
6.Influence of strength of ferrite matrix on yield strength of granular structure steels铁素体基体强度对粒状组织钢屈服强度的影响
7.Experimental research and prediction of yield strength for aging strengthened aluminium alloy铝合金时效强化的实验研究及屈服强度计算
8.Effect of Heat Treatment System and Test Method on Yield Strength of LY12MCZ Alloy热处理制度和试验方法对LY12MCZ屈服强度的影响
9.Yielding strength is indicative of the stress at which plastic deformation begins.屈服强度是指塑性形变开始发生时的应力。
10.EXPERIMENT AND MODELING STUDY OF AGED ALU-MINIUM ALLOYS STRENGTHENING RESPONSE铝合金时效-屈服强度的实验与模型化研究
11.Effects of Heat-treatment Technology on the Yield-Strength of A356 Wheel by Low-Pressure Casting;热处理工艺对A356低压铸造轮毂屈服强度的影响
12.The Influence of Steel Bar Yield Strength Error to Structure Design;钢筋屈服强度的误差对结构设计的影响
13.Effect Factors Analysis on Measuring X80 Grade Pipeline Steel Yield StrengthX80级管线钢管屈服强度测量影响因素的分析
14.Effects of Nb Content on Yield Strength of NiTiNb Alloys in Martensite StateNb含量对NiTiNb合金马氏体态屈服强度的影响(英文)
15.Analysis of Unqualified Strength of 20MnSiV Hot Rolled Ribbed Bars20MnSiV热轧带肋钢筋屈服强度不合原因分析
16.Effect of residual stress on yield strength of air-cooled bainitic steel空冷贝氏体钢的残余应力对屈服强度的影响
17.STRESS-STRAIN BEHAVIORS AROUND THE YIELD STRENGTH IN SEQUENTIAL ROOM TEMPERATURE CREEP TESTS相续室温蠕变中屈服强度附近的应力应变行为
18.Properties of Low Yield Point Steels Used for Earthquake Resistant Buildings建筑抗震阻尼器用低屈服强度钢的性能
相关短句/例句
Micro-yield Strength微屈服强度
1.Through comparison between the micro-yield strength value of and the corresponding yield strength value of more than 130 samples, it is shown that the tedious micro-yield tests can be replaced by common and simple yield tests.通过130多个铍试样的微屈服强度与屈服强度的比较试验证明,用常规简单的屈服强度试验代替冗长的微屈服强度试验是可能的。
2.We research the micro-yield strength of 1Cr18Ni9Ti steel under the high temperature aging treatment,provide mechanical parameters for mechanical engineering.测试1Cr18Ni9Ti合金钢高温时效处理状态下的微屈服强度,为工程实际提供力学参数。
3.Dimensional stability of sub-micron Al2O3 /2024Al composites was studied by means of micro-yield strength measurement and TEM analysis.本文利用微屈服强度测试和透射电镜分析,研究了亚微米级Al_2O_3颗粒增强2024Al复合材料的尺寸稳定性。
3)yield strength屈服强度
1.Effect of phosphorus on theyield strength of as-quenched GH761 alloy;磷对GH761合金固溶水淬组织屈服强度的影响
2.Study of influence factors ofyield strength of oil and gas pipeline;油气管道屈服强度影响因素的研究
3.A modeling study of theyield strength of HRB335 hot rolled ribbed bar;HRB335热轧带肋钢筋屈服强度模型研究
4)yield stress屈服强度
1.Based on the plain carbon steel with the chemical composition of 200MPa class steel the products of theyield stress of 400～500 MPa class and high-quality mechanical properties can be produced using the technology of chemistry tightly-tuning and controlled rolling - controlled cooling.以屈服强度为 2 0 0MPa级的普碳钢为基本成分 ,采用成分微调与控轧控冷工艺相结合的技术路线 ,可将屈服强度提高到 4 0 0～ 5 0 0MPa,同时保证良好的综合性能。
2.From the tests, a two-stage linear relation has been found betweenyield stress(σ_s) and strain rate(ε),σ_s=σ_0+klgε.对４种金属材料进行了应变率为１０~（－４）—１０~３ｓ~（－１）的拉伸试验，结果表明，屈服强度随应变率的升高分两阶段线性升高。
5)yielding strength屈服强度
1.Yielding behavior of mismatched welded joint and prediction of itsyielding strength;非等强焊接接头屈服行为及屈服强度预测
2.Mechanical properties of normalized and tempered 12Cr2Mo steel forgings,primarilyyielding strength,were on the low side.汽轮机用12Cr2Mo钢锻件经正火、回火后,其力学性能(主要是屈服强度)偏低,一次热处理后的合格率仅为50%,既造成该钢锻件大量热处理返修,又严重影响了生产周期。
6)yield point屈服点,屈服强度
延伸阅读
补偿屈服强度分子式：CAS号：性质：应变超过应力-应变曲线成正比例的初始部分的指定量时的应力值。此指定的应变量称残余应变，也称偏置值。报告补偿屈服强度时一定要同时指明此偏置值。此值一般用于该材料没有明显的屈服点的场合。可以认为是一人为规定的屈服点，用于作条件性的相对比较。
