内部冷却系统,internal cooling system
1)internal cooling system内部冷却系统
1.The structure and character ofinternal cooling system of a contact welding machine were developed by Russia scholar.介绍了俄罗斯研制的某接触点焊机中电极内部冷却系统结构及特点。
2)bottom cooling system底部冷却系统
3)cooling system component冷却系统部件
4)internal cooling内冷，内部冷却
5)Cooling system冷却系统
1.Design of gating and cooling system in injection mould for LCD rear cover;液晶显示器后盖注射模浇注与冷却系统设计
2.Design of the cooling system of CD Injection Mould;对光盘注塑模具冷却系统的研究与设计
3.An on-line supervision system for water temperature difference and heat flux intensity in blast furnace cooling system;一种高炉冷却系统水温差及热流强度在线监测技术
英文短句/例句
1.No refrigerant in the refrigerant system.冷却系统中没有冷却剂。
2.Drain cooling system (refer to Group 7, Cooling System).排干冷却系统（见单元7-冷却系统）。
3.gravity circulation water cooling system温差循环液冷却系统
4.spent fuel cooling system辐照燃料元件冷却系统
5.natural circulation type cooling system自然循环液冷却系统
6.the cooling was overhead fans.冷却系统是高架风扇。
7.Not requiring water, as a cooling system.不需水的，如一冷却系统
8.primary reactor coolant system反应堆一次冷却系统
9.thermo-siphon circulation type cooling system热流循环液冷却系统
10.Continue to fill the system until the coolant tank is full.持续填注冷却系统，直到冷却剂贮藏箱填满。
11.Cooling System Simulation Analysis of Transient Heat Transfer and Cooling Performance Calculation;冷却系统瞬态换热仿真分析与冷却性能计算
12.The motor shall be of the air-filled type and shall be cooled by an internal closed loop cooling system.电机应该是风冷式,应该由内置循环冷却系统进行冷却。
13.Cold and hot potable water, HVAC chilled and hot water. Evaporative cooling systems.冷和热饮用水，暖通空调冷却水和热水。蒸汽冷却系统。
14.Fill cooling system (refer to Group 7, Cooling System for the proper procedure).注入冷却系统（有关正确程序请参阅单元7，冷却系统）。
15.a system that cools by evaporation.用蒸发作用冷却的系统。
16.high pressure coolant injection system高压冷却剂注入系统
17.low pressure coolant recirculation system低压冷却剂再循环系统
18.cooling telethermometer冷却(系统的)遥测温度计
相关短句/例句
bottom cooling system底部冷却系统
3)cooling system component冷却系统部件
4)internal cooling内冷，内部冷却
5)Cooling system冷却系统
1.Design of gating and cooling system in injection mould for LCD rear cover;液晶显示器后盖注射模浇注与冷却系统设计
2.Design of the cooling system of CD Injection Mould;对光盘注塑模具冷却系统的研究与设计
3.An on-line supervision system for water temperature difference and heat flux intensity in blast furnace cooling system;一种高炉冷却系统水温差及热流强度在线监测技术
6)the cooling system冷却系统
1.Application of CAE inthe cooling system of injection molding;注射模冷却系统中的CAE技术应用
2.As the property of the plastic,the structure of the plastic production and the parameter of the molding process vary greatly, the temperature required forthe cooling system also differs.注射模冷却系统的设计不但关系到塑件质量而且也关系到注射成型生产效率。
3.The choice and estimation forthe cooling system parameter in the engine cabin is guided.快速而准确地指导发动机舱内冷却系统的参数选择与判定。
延伸阅读
内部内部interior囚都t加挽幻份;皿yT那二ocT‘J拓扑空间X的子集A的满足下列条件的所有点x的集合:存在X中的开集U:，使x任U:CA.集合A的内部通常记为IntA，且表示含于A内的X中的最大开集.等式IntA=x\「X\A」成立，这里〔X}表示X的闭包.拓扑空间X中集合的内部是正则开(化孚血r open)集或典范集(。口训jCalset).其典范开集构成拓扑基(b朋e)的空间称为半正则的(~一记gu~lar).所有正则空间都是半正则的.内部有时也称为集合的开核(open ken祀1 of the set). B .H，floH咖apeB撰【补注1亦见集合的内部(泊忱由r of a set).白苏华、胡师度译
