圆筒型直线感应电机(C-LIM)机构,Cylinder Linear Induction Motor(C-LIM) Mechanism
1)Cylinder Linear Induction Motor(C-LIM) Mechanism圆筒型直线感应电机(C-LIM)机构
2)cylinder cinear induction motor圆筒型直线感应电动机
英文短句/例句
1.Calculation and Analysis of Transient Temperature Field in Tubular Linear Induction Motor圆筒型直线感应电动机瞬态温度场计算与分析
2.Control System Research on Cylindrical Linear Induction Motor Applied to Circuit Breaker Operating Mechanism断路器操动机构用圆筒型直线感应电动机控制系统研究
3.Frnite Element Analysis on Conpound Secondary Eddy Current Loss of Cylindrical Linear Induction Motor圆筒型直线感应电动机复合次级涡流损耗的有限元分析
4.Research on Cylinder Linear Induction Motor Operating Mechanism Used in High-Voltage Circuit Breaker高压断路器圆筒型直线感应电机操动机构研究
5.Numerical Analysis of Starting Characteristics of Tubula Linear Induction Motor圆筒形直线感应电动机的起动特性数值解析
6.Submersible Tubular Linear Permanent-Magnet Synchronous Motor;潜油圆筒型直线永磁同步电动机研究
7.Study on the Optimal Design of Tubular Linear Induction Motor Based on Genetic Algorithm基于遗传算法的圆筒型直线感应电机优化设计研究
8.The Design of Tubular Linear Induction Motor for Lifting and Analysis of Its Starting Characteristics举升用圆筒形直线感应电机设计及起动特性分析
9.Research on the Erection of Cylindrical Linear Motor Model and Dynamic Thermal Field;圆筒型直线电机模型建立及其动态温度场研究
10.Calculation on Key Coefficients of Cylinder Linear PM Motor圆筒型直线永磁电动机的重要系数计算
11.Applicationg of Genetic Algorithms Optimistic Design for Tubular Linear Induction Motor;遗传算法在圆筒型直线电机优化设计中的应用
12.Tubular Linear Motor Thrust Computation and Research of Design Method;圆筒型直线电机推力计算及其设计方法的研究
13.Research on Driving Characteristic of the Linear Induction Motor;直线感应牵引电动机牵引性能的研究
14.The Research and Design of Short-Secondary Linear Induction Motor;长初级直线感应电动机的设计与研究
15.Modeling and dynamics simulation of vehicle with linear induction motor直线感应电机车辆建模与动力学仿真
16.self-oscillating linear induction motor自振荡直线感应电机
17.The vector control mathematical model of linear induction motor is established under the synchronization reference frame.在同步旋转坐标系下，建立了直线感应电动机的矢量控制数学模型。
18.New Equivalent Circuits of Short Primary Single-sided Linear Induction Motor短初级单边直线感应电机新型等效电路
相关短句/例句
cylinder cinear induction motor圆筒型直线感应电动机
3)TLIM圆筒型直线感应电机
1.Tubular linear induction motor (TLIM) is not only cheap but also simple in manufacture, can be widely used in small power drives of short distance.圆筒型直线感应电机具有结构简单,成本低廉等优点,在短行程、小功率的直线运动场合具有广泛的应用前景。
4)tubular linear induction圆筒形直线感应电动机
1.The starting process oftubular linear induction motor was simulated dynamically by Ansoft/Maxwell 2D software which was based on finite element analysis method and the parameters were numerical calculated and analyzed,such as starting thrust,magnetic field density in the air-gap,etc.应用有限元分析软件Ansoft/Maxwell 2D,对圆筒形直线感应电动机的起动过程进行了动态仿真,并对起动推力、气隙磁密等参数进行数值计算和分析。
5)single-phase capacitance tubular linear induction motor单相圆筒型直线感应电机
6)Tubular linear motor圆筒型直线电机
1.Tubular Linear Motor Thrust Computation and Research of Design Method;圆筒型直线电机推力计算及其设计方法的研究
延伸阅读
笼型感应电动机笼型感应电动机cage induction motor;squirrel cage induction motorlongx}ng gonying dlondongJI笼型感应电动机(eage induetion motor;squirrel eage induetion motor)二次绕组(即电机运行时与外部电源不直接连接的绕组)为笼型绕组的感应电动机。笼型绕组为自行闭合的对称多相绕组，它由插人每个转子槽中的导体和两端的环形端环构成。如果去掉铁芯，剩下的绕组外形象个圆笼，因此称为“笼型绕组”，如图所示。大、中型电机常用铜条插人转子槽内，再在两端焊上铜端环，如图(a)所示;小型电机一般都用铸铝转子，转子导体和端环一次铸出，如图(b)所示。笼型感应电动机结构简单、制造方便、经济耐用，所以应用极广。笼型感应电动机只有在最初起动转矩孔:)1.ITL(TL为起动时的负载转矩)时才能正常起动。电动机起动时除考虑起动转矩外，还应考虑起动电流。普通笼型感应电动机的起动电流倍数1.:/人、4~7，起动转矩倍数认:/TN、1~2。这使得大容量笼型感应电动机或要求重载起动的笼型感应电动机往往不能直接起动.降低最初起动电流的方法有:①降低电源电压;②加大 定子边电阻或电抗;③加大转子 边电阻或电抗。加大最初起动转 矩的方法只有适当加大转子电 阻，但不能过分，否则最初起动转 矩反而可能减小。 笼型感应电动机的转子擂形，热;(c)电极通过导电子炉;6一电极;7一过滩板;有单笼、双笼和深槽三种，相应称为单笼型感应电动机、双笼型感应电动机和深槽式感应电动机。一般多采用单笼型感应电动机，如要求具有较高最初起动转矩时，可选用双笼型和深槽式感应电动机，其特点是起动时转子电阻较大，使最初起动转矩增大和最初起动电流减小;正常运行时转子电阻自动变小，使转子铜耗降低。卿环噜笼型绕组(a)铜条笼型绕组;(b)铃铝笼型绕组
