纵横弯曲,vertical and horizontal bend
1)vertical and horizontal bend纵横弯曲
1.This paper has given an error analysis on several common girder undervertical and horizontal bending loads.通过有限元软件“力神”和建筑规范稳定公式两种方法，对各种常见梁在考虑纵横弯曲作用下进行误差分析，从而引入一个系数对规范公式进行修正。
英文短句/例句
1.Research of Influence on Optimum Lifting-point of Concrete Post Due to Bending Vertically and Horizontally纵横弯曲对混凝土柱最优吊点位置影响的研究
2.And I saw the crisscross of twisting turning streets leading to the square.也看到了纵横交错、弯弯曲曲的街从不同方向通往广
3.Reciprocal Theorem Applied for the Bending Thin Plates under Loading in the Plan and Forces Vertical to the Plane;纵横载荷联合作用下弯曲薄板的功的互等定理
4.I gathered all my courage and looked down. I saw the square in the center of the village. And I saw the crisscross of twisting turning streets leading to the square.我鼓足勇气朝下看，看到了村子中心的广场，也看到了纵横交错、弯弯曲曲的街从不同方向通往广
5.Eular crippling stress（纵向弯曲）欧拉临界应力
6.He stood on the bridge over the little winding brook.他站在那座横跨着弯弯曲曲的小溪的桥上。
7.Study on Longitudinal Natural Frequency of Bended Metallicrod弯曲金属杆中纵振动固有频率的研究
8.The CAT System of Normal Stress in Crossbeam Wind横梁弯曲正应力计算机辅助测试系统
9.Bending Stress of Cross-section in Track of Hydraulic Steel Gate水工钢闸门轨道横截面弯曲应力分析
10.Effect of C content on transversal bending property of molybdenum-carbon barsC含量对Mo-C棒横向弯曲性能的影响
11.Calculation model of AFC lateral bending刮板输送机横向推移弯曲段力学模型
12.LONGITUDINAL BUCKLE OF ASYMMETRIC CLADED STAINLESS STEEL PLATES FOR HOT ROLLING非对称不锈钢热轧复合板材的纵向弯曲
13.Flexural vibration of a compound bar piezoelectric transducer复合棒压电纵向振动换能器中的弯曲振动
14.APPROACH OF RELATIONSHIP BETWEEN THE CURVATURE INDEX OF SINGLE BUCKLE FOLD AND STRESS EXPONENT OF THE LAYER单层纵弯褶皱曲率指数与应力指数的关系探讨
15.FEM Simulation of Bending Deformation and Research on Quality Controlling for Truck Lengthwise Beam;车架纵梁弯曲成形模拟分析及质量控制的研究
16.BENDING OF CIRCULAR AND RING-SHAPED ELASTIC THIN PLATE UNDER ARBITRARY LATERAL LOAD任意横向载荷下弹性圆形及圆环形薄板的弯曲
17.Study on Improvement of Transverse Bending Property of Tin-Phosphor Bronze Strip;提高锡磷青铜（QSn6.5-0.1）带材横向弯曲性能研究
18.The Bending Problems of Circular Plate on Transversal Isotropic Elastic Half-space横观各向同性弹性半空间地基上圆板的弯曲
相关短句/例句
vertical and horizontal bending纵横弯曲
1.Influencing factors forvertical and horizontal bending members in frame calculation;框架计算中纵横弯曲分析的影响因素
2.Avertical and horizontal bending calculation of the supporting pole in curtain wall strut-cable structure is presented,and the stability of the pole is discussed.阐述幕墙杆索结构中支撑杆的纵横弯曲计算,并由此讨论杆件的稳定性。
3)Timoshenko beam纵横弯曲梁
1.Distributed transfer function method for timoshenko beam of variable cross-section;用传递函数方法求解变截面纵横弯曲梁
4)beam columns(or links)纵横弯曲杆
5)beam-column method纵横弯曲法
1.This paper first introduces process of modeling in Pro/MECHANICA,then shows the application efficiency ofbeam-column method in Pro/MECHANICA through an example.首先介绍了纵横弯曲法在Pro/MECHANICA中的建模过程,然后通过一个实例来说明纵横弯曲法在Pro/MECHANICA中的应用效果,并与编程计算得到的结果进行了比较。
6)Crossbar Bent Continuous Beam Law纵横弯曲连续梁法
延伸阅读
弯曲工艺的概念及弯曲件1．弯曲工艺：是根据零件形状的需要，通过模具和压力机把毛坯弯成一定角度，一定形状工件的冲压工艺方法。 2．弯曲成形工艺在工业生产中的应用：应用相当广泛，如汽车上很多履盖件，小汽车的柜架构件，摩托车上把柄，脚支架，单车上的支架构件，把柄，小的如门扣，夹子（铁夹）等。 弯曲的基本原理：以V形板料弯曲件的弯曲变形为例进行说明。其过程为： 1． 凸模运动接触板料（毛坯）由于凸,凹模不同的接触点力作用而产生弯矩， 在弯矩作用下发生弹性变形，产生弯曲。 2． 随着凸模继续下行，毛坯与凹模表面逐渐靠近接触，使弯曲半径及弯曲力臂均随之减少，毛坯与凹模接触点由凹模两肩移到凹模两斜面上。（塑变开始阶段）。 3．随着凸模的继续下行，毛坯两端接触凸模斜面开始弯曲。（回弯曲阶段）。 4．压平阶段，随着凸凹模间的间隙不断变小，板料在凸凹模间被压平。 5． 校正阶段，当行程终了，对板料进行校正，使其圆角直边与凸模全部贴合而成所需的形状。 弯曲变形的特点：弯曲变形的特点是：板料在弯曲变形区内的曲率发生变化，即 弯 曲半径发生变化。从弯曲断面可划分为三个区：拉伸区、压缩区和中性层。
