弯曲承载,bending load
1)bending load弯曲承载
1.So, this paper aimed to pallet\"sbending load property ,and did the following research and analysis.为此,本文以研究托盘弯曲承载特性为目标,进行了以下方面的研究与分析。
英文短句/例句
1.ANALYSIS ON FLEXURAL CAPACITY AND DUCTILITY OF STEEL REINFORCED ULTRAHIGH TOUGHNESS CEMENTITIOUS COMPOSITE BEAMS钢筋增强超高韧性水泥基复合材料梁的弯曲承载力及延性分析
2.Distortional Buckling Strength and Interaction Bending Capacity of Flexural Cold-Formed Lipped Channels受弯的冷弯卷边槽钢畸变屈曲强度和其相关屈曲承载力
3.Finite Element Analysis of Derrick Bearing Capacity with Bending Bar含弯曲杆件的井架承载能力有限元分析
4.RANALYSIS OF STABLE BEARING CAPACITY OF STEEL FRAMES WITH SEMI-RIGID CONNECTION AND ORIGINAL CURVATURE考虑初弯曲的半刚接钢框架稳定承载力分析
5.The In-Plane Stability Carrying Capacity Analysis of Beam-Columns Considering the Post-Buckling Strength of the Web;考虑腹板屈曲后强度压弯构件平面内稳定承载力研究
6.Probability of Flexural Fatigue and Straight-resistance of Steel Fiber Reinforced Prestressed Concrete Slab;预应力钢纤维混凝土板的弯曲疲劳性能及正截面承载力计算
7.Nonlinear Bending Analysis of Simply Supported Plates with Immovable Edges by Using the Perturbation Differential Quadrature Method;承受均匀载荷的固定夹紧板的非线性弯曲的摄动DQ解
8.As one of several strength-governing modes, distortional buckling is receiving more attentions.作为控制冷弯薄壁型钢承载能力的几种屈曲模式之一，畸变屈曲正逐步受到重视。
9.Influence of Training with Secondary Load on Bending Fatigue Strength of Cranksh aft次载锻炼对曲轴弯曲疲劳强度的影响
10.Cold-Formed Steel Unlipped Channels Subjected to Concentrated Bearing Load;冷弯薄壁非卷边槽钢承受集中荷载时的承载力
11.The limit bending capacity of a round-corner-rolled crankshaft is measured with the testing machine.利用该试验机对日本大发公司生产的经过圆角滚压处理的曲轴的极限承载弯矩进行了测试。
12.Research on Flexural Capacity of Cold-formed Thin-wall Steel-Concrete Composite Beam;冷弯薄壁型钢—混凝土组合梁抗弯承载性能研究
13.testing method for stiffness of paper by bending load纸的弯曲负载下刚性试验方法
14.Experiment and Theory Study on Incremental In-Plane Bending;非连续加载面内弯曲实验与理论研究
15.Bending Calculation of Bimodulous Circular Plate under Concentrated Loads集中载荷作用下双模量圆板弯曲计算
16.The smallest load capable of maintaining the bar in a slightly bent form is called the critical or bucking load.使杆保持稍微弯曲形状的最小载荷称为临界载荷或临界压曲载荷。
17.Simulate experimental study on bending bearing capacity of the colour steel sandwich panel彩钢夹芯板受弯承载力模拟试验研究
18.Study on Stability Capacity of Aluminium Beam-Columns;铝合金结构压弯构件稳定承载力研究
相关短句/例句
flexural capacity弯曲承载力
3)ultimate moment capacity弯曲极限承载力
1.An approximate method for predicting theultimate moment capacity of the beams with notches was put forward.进行受拉区带缺口钢筋混凝土梁和无缺口梁的对比实验，分析带缺口梁的承载机理，提出一种近似计算弯曲极限承载力的方法。
2.This paper first proves that the plane deformation assumption conventionally used for a longtime leads to an under-estimate ofultimate moment capacity of weldmesh ferrocement.本文首先证明沿用多年的平面变形假设导致对焊接钢丝网水泥弯曲极限承载力的过低估计，进而采用一新的矩形应力分布假定，计算极限弯曲承载力。
4)lateral-torsional buckling resistance弯扭屈曲承载力
1.Based on the latest experimental study abroad,lateral-torsional buckling resistance of coped beams has been analyzed in this .由于几何，材料非线性，初始几何缺陷及切口参数等因素，使得切口梁弯扭屈曲承载力的确定比较复杂。
5)flexural capacity of RUHTCC beamRUHTCC梁弯曲承载力
6)variation factor of flex-ural resistance弯曲承载力变化系数
延伸阅读
弯曲工艺的概念及弯曲件1．弯曲工艺：是根据零件形状的需要，通过模具和压力机把毛坯弯成一定角度，一定形状工件的冲压工艺方法。 2．弯曲成形工艺在工业生产中的应用：应用相当广泛，如汽车上很多履盖件，小汽车的柜架构件，摩托车上把柄，脚支架，单车上的支架构件，把柄，小的如门扣，夹子（铁夹）等。 弯曲的基本原理：以V形板料弯曲件的弯曲变形为例进行说明。其过程为： 1． 凸模运动接触板料（毛坯）由于凸,凹模不同的接触点力作用而产生弯矩， 在弯矩作用下发生弹性变形，产生弯曲。 2． 随着凸模继续下行，毛坯与凹模表面逐渐靠近接触，使弯曲半径及弯曲力臂均随之减少，毛坯与凹模接触点由凹模两肩移到凹模两斜面上。（塑变开始阶段）。 3．随着凸模的继续下行，毛坯两端接触凸模斜面开始弯曲。（回弯曲阶段）。 4．压平阶段，随着凸凹模间的间隙不断变小，板料在凸凹模间被压平。 5． 校正阶段，当行程终了，对板料进行校正，使其圆角直边与凸模全部贴合而成所需的形状。 弯曲变形的特点：弯曲变形的特点是：板料在弯曲变形区内的曲率发生变化，即 弯 曲半径发生变化。从弯曲断面可划分为三个区：拉伸区、压缩区和中性层。
