车轴强度,Axle strength
1)Axle strength车轴强度
英文短句/例句
parison and Analysis of the Calculation Methods for the Axle Strength of High-Speed Train高速列车车轴强度计算方法对比分析
2.Strength Analysis about Trailer Wheelset and Axle-box of CRH_2;CRH_2动车组拖车轮对轴箱强度分析
3.RUGGEDNESS. Automotive ring gear differential. Axle shafts on roller bearings.强度：自动差速齿轮，滚子轴承上的刚性车轴。
4.Structural Strength Analysis of Constant Velocity Joints for Car Drive-shaft by Finite Element Method;轿车驱动轴等速万向节结构强度的有限元分析
5.Strctural Strength Finite Element Analysis of Automotive Constant Velocity Drive-shaft;汽车等速驱动轴结构强度的有限元分析
6.Multi-Axial Fatigue Strength Analysis of Wheel Based on FEA基于有限元仿真车轮多轴疲劳强度分析
7.Fatigue Strength Evaluation Method of Welded Frame of Four-Axle Wagon4D轴货车焊接构架的疲劳强度分析方法
8.Study on Fatigue Strength of Nodular Graphite Cast Iron Crankshaft of Locomotive High Speed Diesel Engine内燃机车用高速柴油机球铁曲轴疲劳强度的试验研究
9.FINITE ELEMENT RESEARCH ON STRESS INTENSITY FACTORS AT THE FRONT OF SURFACE CRACK OF HOLLOW AXLES空心车轴表面裂纹前缘应力强度因子的有限元研究
10.Optimization Design of Bearing for Internal Combustion Engine Considering Crankshaft Strength;计及曲轴强度的内燃机轴承优化设计
11.Analytical Investigation on Strength and Main Bearing Lubrication of CA4D32 Diesel Engine Crankshaft System Based on a Simulation Technique;柴油机曲轴轴系强度和主轴承润滑仿真研究
12.Coupling Research on Tribology, Stiffness and Strength of Crankshaft-bearing System;曲轴—轴承系统摩擦学、刚度和强度的耦合研究
13.Experimental Study on Dynamic Strength and Deformation of Concrete Under Uniaxial and Blaxial Action;混凝土单轴、双轴动态强度和变形试验研究
14.The Performance Analysis of Diesel Crankshaft and the Research for Calculation Method of Crankshaft Fatigue Strength;柴油机曲轴性能分析及曲轴强度计算方法研究
15.Calculation of Dynamic Stress and Fatigue Strength of Crankshaft with Bush Deformation Included计入轴瓦变形的曲轴动应力和疲劳强度计算
16.The Research on Equal-strength Design of Large-scale Heavy-load Cross-shaft Universal Clutch大型重载十字轴式万向联轴器等强度设计研究
17.crankshaft (main journal turning lathe)曲轴（主轴颈）车床
18.camshaft(journal )turning lathe凸轮轴（轴颈）车床
相关短句/例句
tensile strength轴拉强度
1.The main objective of the tests is to determine the relationship between thetensile strength and splitting strength of steel fiber reinforced concrete(SFRC).分析研究了钢纤维高强混凝土的轴拉强度和劈拉强度的关系,钢纤维高强混凝土轴拉性能随钢纤维体积掺量、基体强度及钢纤维类型的变化规律。
2.With raw materials of Jinping first-level hydropower station,the experimental study on performance of hydraulic concrete with magnesia shows that the compressive strength of concrete added with magnesia is descreased slightly and cleavage strength,tensile strength,modulus of elasticity,tensile strain ultimate of concrete added with magnesia are increased slightly.通过采用锦屏一级水电站的原材料,对外掺氧化镁的水工混凝土性能试验研究表明,外掺氧化镁对混凝土的抗压强度略有降低,对劈拉强度、轴拉强度、弹性模量、极限拉伸值略有提高;未掺氧化镁的砂岩混凝土180d自身体积变形为-57。
3)axial compression strength轴压强度
1.Influence of edge effects onaxial compression strength for filament wound cylinder;端面边缘效应对缠绕管件轴压强度的影响
4)pump shaft intensity泵轴强度
1.A finite element analysis of the pulppump shaft intensity;纸浆泵泵轴强度的有限元分析
5)uniaxial strengeth单轴强度
6)main axe intensity主轴强度
延伸阅读
轴向强度分子式：CAS号：性质：取向聚合物沿取向轴方向的强度。单轴取向的聚合物材料(如纤维)由于分子链或链段沿取向方向定向排列，其轴向拉伸强度很高。单轴取向的薄膜(如撕裂薄膜)，其轴向强度较高，而垂直取向方向的强度却极差；双轴取向的薄膜，则在膜平面的任何方向都具有较高的强度。
