风洞拐角,wind tunnel corner
1)wind tunnel corner风洞拐角
1.Application and comparison of calculation of two turbulence models on flow field ofwind tunnel corner两种湍流模型在风洞拐角流场计算中的应用及比较
英文短句/例句
1.Application and comparison of calculation of two turbulence models on flow field of wind tunnel corner两种湍流模型在风洞拐角流场计算中的应用及比较
2.a breezy corner, beach, hillside风凉的拐角处、 沙滩、 山坡.
3.Turn the second corner to the left .在第二个拐角处向左拐。
4.Turn the first corner to the right .在第一个拐角处向右拐。
5.A Numerical Wind Tunnel Study on Distance between Tail Wing and Rear Hood and Angle of Attack of Tail Wing of a Car Model Using CFD;轿车尾翼间隙和攻角的数值风洞研究
6.Wind Tunnel Investigation on Dynamic behavior of 80°/65° Double Delta Wing in Rolling at High Incidence80°/65°双三角翼摇滚特性风洞实验研究
7.The development of high angle of attack test equipment in the 8m×6m low speed wind tunnel8m×6m风洞特大迎角试验设备研制
8.around the bushph.1. 拐弯抹角
9.Watch the ball wind down spiraling slopes, escape the windmill"s blade, and drop into the hole.观察风的角度，避免风力的影响，一杆进洞。
10.Double corner curb. Corner radius can be specified.双拐角路缘。可指定拐角的半径。
11.Single corner curb. Corner radius can be specified.单拐角路缘。可指定拐角的半径。
12.The Xinhua News Agency Monday accuses the labor supervision department in Shanxi province"s Hongdong county of taking part in the child labor trade, and of warning kiln owners who were under investigation.新华社星期一指称山西洪洞县劳动监管部门参与拐卖童工并向被调查的窑主通风报信。
13.The measurement and control of the model attitude angle in airfoil wind tunnel test翼型风洞实验模型姿态角的测量与控制
14.4m×3m LOW-SPEED TUNNEL MODEL ATTITUDE ANGLE CONTROL SYSTEM4米×3米低速风洞模型姿态角控制系统
15.Wind tunnel experiment of sidewall compression inlet with adjustable attack angle攻角动态变化的侧压式进气道风洞实验
16.full scale wind tunnel整车风洞或全尺寸风洞
17.Well, turn to the left at the first corner after the crossroads.噢，过十字路口后在第一个拐角向左拐。
18.About three hundred yards farther on there is a turning to the left.再往前大约300码有一个向左拐的拐角。
相关短句/例句
corner void拐角空洞
3)corner[英]["k?:n?(r)][美]["k?rn?]拐角
1.On the basis of residual areas after rough machining,a tool path generation algorithm for residual material fine machining at thecorners of pocket boundary was developed and implemented in consideration of even radial cutting depth and smooth tool path.在识别粗加工余料区域的基础上,从均匀径向切削深度、平滑刀轨路径等方面考虑,研究并实现了型腔边界拐角处的精加工刀轨生成算法。
2.Sharp turningcorners of the tool path are rounded, and the transition from a tool path track to the neighboring one is fulfiled through smooth curves.在常规的环切刀轨生成算法基础上 ,设计了型腔高速铣削加工刀轨生成算法 对刀轨的拐角进行了平滑处理 ,实现了相邻刀轨环之间的光滑曲线过渡 ,避免了刀具运动方向的急剧变化 ,可使切削性能得到改
3.General linear and nonlinear smoothing in an intensity image can blurcorners seriously, so it s difficult to detectcorners by a multi scale approach.对灰度图进行一般线性和非线性平滑会极大程度地模糊拐角 ,使得多尺度方法难以用于拐角检测 。
4)corner[英]["k?:n?(r)][美]["k?rn?]拐角，角落
5)corner reconstruction拐角重构
6)corner R拐角R
1.A special two-chamber continuous-quenching inductor and the process in which cooling water and quenchant are controlled respectively,are adopted to deal with the problem of intermediate-frequency induction hardening oncorner R.针对台阶轴拐角R处难以实现感应淬火的问题,设计了一种特殊的双室水路连续淬火感应器。
延伸阅读
癌性空洞癌性空洞病理学术语。肺癌内部形成的空洞，发生率约为10%～20%，主要见于周围型肺癌，以鳞癌居多。形成原因多认为与癌组织液化、坏死或感染等因素有关。影像学特点是：①空洞壁厚而不均，内壁凸凹不平，有结节影向腔内突出。②空洞内多无液平，个别肺癌呈薄壁腔样表现，洞壁虽光滑整齐，但仍有薄厚不均的表现，可提示诊断。
