钢水成分,steel composition
1)steel composition钢水成分
1.Regression analysis on end-pointsteel composition and temperature for top and bottom blowing converter;顶底复吹转炉冶炼终点钢水成分及温度回归预测分析
2.For the quantity of triangular area crack and central area crack of SS400 slab,analysis is carried out onsteel composition,degree of superheat,casting gap,etc.针对SS400钢铸坯出现大量三角区裂纹和中心裂纹的现象,从钢水的成分、浇铸过热度、扇形段开口度等方面进行分析,通过采取控制钢水成分、保证铸机精度、优化二次冷却等措施,有效地控制了板坯的三角区裂纹和中心裂纹,铸坯一次合格率由94。
2)Liquid Steel Composition钢液成分
3)ingredient of steel钢成分
4)ingot composition钢锭成分
1.with electroslap remelting are researched, some measures adopted to guarentee theingot composition qualified and homogeneous from head to tail.研究了电渣重熔W6MoSCr4V2Al（M2Al）过程中影响钢锭Si、Al成分的因素，采取针对措施，确保了钢锭成分合格且头尾成分一致。
英文短句/例句
1.Software of Prediction Model Based on Artificial Neural Network for Steel Ingredients基于BP神经网络预报钢锭成分的软件开发
2.Some CO gas remains in the ingot, and eventually blow holes are formed in the steel.部分一氧化碳气体残留在钢锭内部，最终在钢中形成气泡。
3.So less gas is given off in the mould than with rimming steel, but enough bubbles form at the top of the ingot to counteract most of the shrinkage,所以，在钢锭模内析出的气体没有沸腾钢多，但又在钢锭头产形成足够的气泡抵消大部分钢的收缩。
4.Steel windows, in general, are made from hot-rolled,structural grade new billet steel.However,for double-hung windows,the principal members are cold-formed ftom new billet strip steel.钢窗一般用新钢锭热轧结构钢制成。但上下推拉窗的主要构件要用新带钢钢锭冷加工成形。
5.mould setting-and-stripping bay钢锭模准备和脱锭跨
6.QUANTITATIVE ANALYSIS OF BENEFITS OF CHARGING TEMPERATURE OF STEEL INGOT OF SOAKING PIT均热炉钢锭装炉温度效益的定量分析
7.Generally it goes through two stages to convert steel ingots into rolled steels by rolling.一般说来，把钢锭轧制成钢材要经过两个阶段。
8.Dynamic Analysis of Ring/Taveller System in Ring Spinning;环锭纺纱钢领、钢丝圈系统的动态性能分析
9.According to the calculation of interface energy as well as the flow analysis based on gravity, it is claimed that the inclusions distribution was affected by the travel of the excessive[ H] during solidification.采用相间能计算和重力流动分析得知,此分布规律是过量[]钢锭凝固过程中的运动促成的。
10.Surface pinholes caused by gas formed at the mould surface.因钢锭模表面生成气体而形成的表面针孔。
11.Investigation on Thermal Stress Distribution of Cr5 Large-scale Alloy Steel Ingot by SimulatingCr5大型合金钢铸锭热应力状态的模拟分析
12.The textile industry, one facing enormous difficulties, reduced 2.8 million spindles in the first half of this year, and redirected 400,000 redundant workers.困难较大的纺织行业上半年完成压锭280万锭，分流富余人员40万人。
13.The inclusions distribution in ingot was examined by means of microscopy.通过对解剖钢坯的金相检验,找出了夹杂物在钢锭中的分布规律。
14.Rings for ring-spinning and ring-doubling frames环锭纺和环锭捻线机钢领
15.cable-driven ingot buggy钢丝绳牵引的送锭车
16.The moulds are made of cast iron.钢锭模是用铸铁做的。
17.overhead ingot turning and weighing machine架空式钢锭回转称量机
18.Centreline shrinkage may form a serious line of weakness in the ingot. Surface defects include the following:轴线缩孔可在钢锭中形成一条很长的疏松线。表面缺陷有如下几类:
相关短句/例句
Liquid Steel Composition钢液成分
3)ingredient of steel钢成分
4)ingot composition钢锭成分
1.with electroslap remelting are researched, some measures adopted to guarentee theingot composition qualified and homogeneous from head to tail.研究了电渣重熔W6MoSCr4V2Al（M2Al）过程中影响钢锭Si、Al成分的因素，采取针对措施，确保了钢锭成分合格且头尾成分一致。
5)molten steel analysis钢水分析
6)composition controlling for IF steelIF钢成分控制
延伸阅读
钢水液体状态的钢。钢水一般都铸成钢锭，也可以直接浇铸成铸件。
